GPS Connections: SatLoc G4 Connections Or Ag Nav Plat Connections
AgPilot X Connections , TracMap Connections Or VeriFly Connections
Wingman / Loadhog Seal Images to show a seal setup that has been working
Gate Issue List or Solved Issues
YouTube aid Videos:
Gate Pilot Guide YouTube Playlist
Gate Trouble Shooting YouTube Playlist
Patents:
Gate Software and how to update:
You Tube Showing controller update. https://youtu.be/DXnHncJ06yw
A0 127 Updated NoSel Flow estimate, Better first load estimate.
A0 126 Added, Liquid CleanOut Percent and Constant Rate Startup settings in Setup menu.
A0 125 Added Internal communication reset if data string error seen.
A0 124 Turned off un-used GPS Data Port, added Delay and Debounce for Liquid/Dry Mode change.
A0 123 Added Software Code check at startup, See if software got corrupted.
A0 122 Added HopSpeed View sub menu to aid in finding and setting hop speed.
A0 121 Software change to speed up pin read in Interrupt Service Routine (ISR, run code faster)
A0 120 Software change to shorten Interrupt Service Routine (ISR, run code faster)
A0 119 Added TracMap GPS
A0 118 7.5″ gate max open set to 5.5″, Min HopSpeed changed from -20 to -40
A0 117 Set max Chemical Correction Value, So unit can not calibrate to an instant run out.
A0 116 Added auto reset for start up lockups
A0 115 Fixed Metric Swath settings.
A0 114 Added U-Blox GPS for Constant rate Application (only Select U-Blox GPS if U-Blox GPS is connected)
A0 T 113 Added AgPilot X Variable Rate, (this is using Beta software from AgPilot X, Will post non-test “T” firmware when testing is complete)
A0 112 Added TRIM pass function and Setup menu Setting
A0 111 Added the Ability to accept a Load Cal Error After takeoff during Flight
A0 110 Increase 7.5″ Gate open setting
A0 109 Fixed Satloc + protocol message error, Use in place of A0 107, or A0 108
A0 108 Worked on Find Stops and Jam conditions to limit current spikes an motor Jerk
A0 107 “Satloc +” Added to GPS options New non relay Auto On/Off, “Satloc” changed to “Satloc L” (legacy) Must have Satloc Software 3.22.171.1748 or Later and Reabe Smart Gate (RSM or REG) unlock for G4.
A0 106 Added software for Ag Nav GPS
A0 105 Update to add Auto On/Off for AgPilotX GPS. See AgPilotX install notes for required software and firmware versions
A0 104 Update to Constant Rate-rate mode, made unit take Swath width from GPS in Variable Rate mode
A0 103 Added Gate Open indication when in Liquid Mode, Added CAN BUS fault info and auto motor reset
A0 102 Added CAN bus for AgPilot X, Set Auto On/Off Time out to .25 Seconds for loss of command, Fixed GPS Fail screen lockup
A0 101 Added “HopPaint” to setup When on GPS Paint relay shuts off when Hopper Pressure drops, Marking the end of where you ran out. (must have GPS paint Relay installed)
A0 100 Added Negitive values to HopSpeed Setting
Switching between software versions above or Below A0 99 you will need to go into setup and reset your HopSpeed Value after the Update
A0 12 Motor is off when closed and stowed, Increased Locked Zone, Smoother Find Stops, Added 7.5″ gate.
A0 11 Increased the input torque to take Manual Control of the Gate
A0 10 Removed Hopper Valve Sensing from Spray On/Off Relay Control
A0 09 Has Larger range to accept motor home position. “MOTR POS” 350 to 2550
A0 08 has the updates of A0 07 and the needed communication for SatLoc Auto On/Off
A0 07 has the updates of A0 06 and a little more power added to close the gate for the heavy material.
A0 06 is the Software with the .025″ gate adjustments and a fixed GPS rs-232 connection so gate works with liquid flow control.
A0 05 is the software the gate shipped with in case you need to go back